Maxx Model M4 / M16 CNC Alu HopUp Unit M4I PRO for ICS -silver-
![ICS M1 Garand HopUp Unit [ME-14]](https://www.begadi.com/media/catalog/product/cache/a491986f8011072f66fb1fed37f51dcc/e/9/e976bd5a4410442625f904e823a09d9a.jpg)
This HopUp Unit fits especially for M4/M16 AEG models from ICS.
For regular M4/M16 models, Maxx Model offers its own unit (M4A), which can be found in the store under item number 18522010.
Please refer to the installation instructions + information on compatibility below
What's new with the M4A and M4I?
The side wings can be removed, which is important for outer barrels that do not comply with the standard.
The available tensioners have also been revised and offer more options than their predecessor.
Features:
- CNC machined from one block of 6061 aluminum
- BB Latching System prevents BBs from falling out of the feeding tube when changing the magazine
- Built-in adjustment wheel for precise, stepless adjustment
- Nozzles from 21.00 - 21.25mm can be used
- Compatible with most third-party HopUp rubbers
- 2 transparent vinyl plates are attached to the side, which allow a clear view of the BBs still present in the HopUp Chamber
- 3 tensioners are included in the delivery. (only for 5mm systems)
BB Latching System:
Please note that this system is not compatible with all magazines and different manufacturers. Unfortunately, Begadi cannot give any warranty for the different systems.
LED Tracer Board:
The M4A and M4i are no longer compatible with the LED Tracer Board V2.
Dimensions:
Length: 51mm
Height: 38.80mm
Outerbarrel diameter: min. 12mm
Nozzle diameter: max. 7.8mm
Feeding tube diameter: 8.9mm
Feeding tube length: 6mm
Installation instructions:
The following points should be taken into account when installing the Hop Up Unit:
It may be necessary to change the nozzle. MAXX expressly recommends a nozzle length of 21.00mm to a maximum of 21.25mm in its installation instructions.
Standard M4 nozzles usually have a length between 21.2mm - 21.4mm which can lead to feeding problems when using this hop up unit.
We generally recommend that you order a suitable nozzle at the same time.
Notes on compatibilities:
Not compatible with Begadi Sport/Cyma models (adjustment wheel too large, nozzle not compatible)
Scope of delivery:
- HopUp Unit
- Adjustment wheel (installed)
- Inlet (11.9mm, installed)
- C-Clip
- Tensioner for 5mm systems (flat, rubber)
- Tensioner for 5mm systems (rounded, aluminum)
- Tensioner for 5mm systems (3mm round, rubber)
- Barrel spring
- Spring for outer barrel (built-in)
- Brass ring
- O-ring for inner barrel
Links & Downloads:
-Maxx Model M4 / M16 CNC Alu HopUp Unit M4I PRO for ICS -silver-, instruction manual sheet 1
- Maxx Model M4 / M16 CNC Alu HopUp Unit M4I PRO for ICS -silver-, instruction manual sheet 2
- Delrin C-Clip for Maxx Model HopUp Units
Comparison pictures M4A PRO + M4I PRO:
Comparison pictures to the model predecessor MI PRO:
For regular M4/M16 models, Maxx Model offers its own unit (M4A), which can be found in the store under item number 18522010.
Please refer to the installation instructions + information on compatibility below
What's new with the M4A and M4I?
The side wings can be removed, which is important for outer barrels that do not comply with the standard.
The available tensioners have also been revised and offer more options than their predecessor.
Features:
- CNC machined from one block of 6061 aluminum
- BB Latching System prevents BBs from falling out of the feeding tube when changing the magazine
- Built-in adjustment wheel for precise, stepless adjustment
- Nozzles from 21.00 - 21.25mm can be used
- Compatible with most third-party HopUp rubbers
- 2 transparent vinyl plates are attached to the side, which allow a clear view of the BBs still present in the HopUp Chamber
- 3 tensioners are included in the delivery. (only for 5mm systems)
BB Latching System:
Please note that this system is not compatible with all magazines and different manufacturers. Unfortunately, Begadi cannot give any warranty for the different systems.
LED Tracer Board:
The M4A and M4i are no longer compatible with the LED Tracer Board V2.
Dimensions:
Length: 51mm
Height: 38.80mm
Outerbarrel diameter: min. 12mm
Nozzle diameter: max. 7.8mm
Feeding tube diameter: 8.9mm
Feeding tube length: 6mm
Installation instructions:
The following points should be taken into account when installing the Hop Up Unit:
It may be necessary to change the nozzle. MAXX expressly recommends a nozzle length of 21.00mm to a maximum of 21.25mm in its installation instructions.
Standard M4 nozzles usually have a length between 21.2mm - 21.4mm which can lead to feeding problems when using this hop up unit.
We generally recommend that you order a suitable nozzle at the same time.
Notes on compatibilities:
Not compatible with Begadi Sport/Cyma models (adjustment wheel too large, nozzle not compatible)
Scope of delivery:
- HopUp Unit
- Adjustment wheel (installed)
- Inlet (11.9mm, installed)
- C-Clip
- Tensioner for 5mm systems (flat, rubber)
- Tensioner for 5mm systems (rounded, aluminum)
- Tensioner for 5mm systems (3mm round, rubber)
- Barrel spring
- Spring for outer barrel (built-in)
- Brass ring
- O-ring for inner barrel
Links & Downloads:
-Maxx Model M4 / M16 CNC Alu HopUp Unit M4I PRO for ICS -silver-, instruction manual sheet 1
- Maxx Model M4 / M16 CNC Alu HopUp Unit M4I PRO for ICS -silver-, instruction manual sheet 2
- Delrin C-Clip for Maxx Model HopUp Units
Comparison pictures M4A PRO + M4I PRO:
Comparison pictures to the model predecessor MI PRO:
Review Partner