CNC Back Cover Set for Begadi Mamba Motors - black
CNC manufactured back cover, suitable for our Begadi Mamba Motors.
This is a set that is very easy to install.
Insulators, plugs and the Bearing are already pre-assembled.
The entire back cover can be replaced by loosening the two screws.
Then just insert the carbon brushes with Springs.
Begadi Service: In the picture section of the offer you will find step-by-step illustrated instructions with information on (dis)assembly.
Suitable for the following Motors:
- Begadi Mamba 39K
- Begadi Mamba 30K
- Begadi Mamba 28K
- Begadi Mamba 19K
- Begadi Mamba 15K
If you need new carbons, you can find them HERE
Product views of the CNC Back Cover Set:
(Dis)assembly instructions - disassembly part - step 1:
Shows a still fully assembled back cover.
(Dis)assembly instructions - disassembly part - step 2:
Now remove Springs and carbons.
(Dis)assembly instructions - Disassembly part - Step 3:
Now remove the screws together with the washers.
(Dis)assembly instructions - Disassembly part - Step 4:
Detach the cover from the engine block. Make sure that the old Bearing is also removed. In this condition, the Motor could also be cleaned with brake cleaner (if already older). Work cleanly so that no foreign bodies get into the Motor.
(Dis)assembly instructions - Fitting the new cover - Step 5:
Now mount the new cover on the motor shaft. As our Mamba Motors have very strong magnets, you will need to apply some force in this step, as you will have to work against the magnetic force. Be careful not to damage the internal Bearing.
(Dis)assembly instructions - Fitting the new cover - Step 6:
Now fit the screws. Tighten them hand-tight.
(Dis)assembly instructions - Fitting the new cover - Step 7:
Now fit the carbon brushes. If your carbon brushes are already worn down, new ones can be fitted directly here. Ensure that they are correctly aligned.
(Dis)assembly instructions - Fitting the new cover - Step 8:
Now fit the Springs so that the carbons are pressed inwards against the collector.
This is a set that is very easy to install.
Insulators, plugs and the Bearing are already pre-assembled.
The entire back cover can be replaced by loosening the two screws.
Then just insert the carbon brushes with Springs.
Begadi Service: In the picture section of the offer you will find step-by-step illustrated instructions with information on (dis)assembly.
Suitable for the following Motors:
- Begadi Mamba 39K
- Begadi Mamba 30K
- Begadi Mamba 28K
- Begadi Mamba 19K
- Begadi Mamba 15K
If you need new carbons, you can find them HERE
Product views of the CNC Back Cover Set:
(Dis)assembly instructions - disassembly part - step 1:
Shows a still fully assembled back cover.
(Dis)assembly instructions - disassembly part - step 2:
Now remove Springs and carbons.
(Dis)assembly instructions - Disassembly part - Step 3:
Now remove the screws together with the washers.
(Dis)assembly instructions - Disassembly part - Step 4:
Detach the cover from the engine block. Make sure that the old Bearing is also removed. In this condition, the Motor could also be cleaned with brake cleaner (if already older). Work cleanly so that no foreign bodies get into the Motor.
(Dis)assembly instructions - Fitting the new cover - Step 5:
Now mount the new cover on the motor shaft. As our Mamba Motors have very strong magnets, you will need to apply some force in this step, as you will have to work against the magnetic force. Be careful not to damage the internal Bearing.
(Dis)assembly instructions - Fitting the new cover - Step 6:
Now fit the screws. Tighten them hand-tight.
(Dis)assembly instructions - Fitting the new cover - Step 7:
Now fit the carbon brushes. If your carbon brushes are already worn down, new ones can be fitted directly here. Ensure that they are correctly aligned.
(Dis)assembly instructions - Fitting the new cover - Step 8:
Now fit the Springs so that the carbons are pressed inwards against the collector.
